# LCDd.conf -- configuration file for the LCDproc server daemon LCDd # # This file contains the configuration for the LCDd server. # # The format is ini-file-like. It is divided into sections that start at # markers that look like [section]. Comments are all line-based comments, # and are lines that start with '#' or ';'. # # The server has a 'central' section named [server]. For the menu there is # a section called [menu]. Further each driver has a section which # defines how the driver acts. # # The drivers are activated by specifiying them in a driver= line in the # server section, like: # # Driver=curses # # This tells LCDd to use the curses driver. # The first driver that is loaded and is capable of output defines the # size of the display. The default driver to use is curses. # If the driver is specified using the -d command line option, # the Driver= options in the config file are ignored. # # The drivers read their own options from the respective sections. ## Server section with all kinds of settings for the LCDd server ## [server] # Where can we find the driver modules ? # IMPORTANT: Make sure to change this setting to reflect your # specific setup! Otherwise LCDd won't be able to find # the driver modules and will thus not be able to # function properly. # NOTE: Always place a slash as last character ! DriverPath=/usr/lib/lcdproc/ # Tells the server to load the given drivers. Multiple lines can be given. # The name of the driver is case sensitive and determines the section # where to look for further configuration options of the specific driver # as well as the name of the dynamic driver module to load at runtime. # The latter one can be changed by giving af File= directive in the # driver specific section. # # The following drivers are supported: # bayrad, CFontz, CFontz633, CFontzPacket, curses, CwLnx, ea65, # EyeboxOne, g15, glcdlib, glk, hd44780, icp_a106, imon, imonlcd, IOWarrior, # irman, joy, lb216, lcdm001, lcterm, lirc, lis, MD8800, ms6931, mtc_s16209x, # MtxOrb, mx5000, NoritakeVFD, picolcd, pyramid, sed1330, sed1520, serialPOS, # serialVFD, shuttleVFD, sli, stv5730, svga, t6963, text, tyan, ula200, # xosd #Driver=curses Driver=MtxOrb # Tells the driver to bind to the given interface Bind=127.0.0.1 # Listen on this specified port; defaults to 13666. Port=13666 # Sets the reporting level; defaults to 2 (warnings and errors only). #ReportLevel=3 # Should we report to syslog instead of stderr ? [default: no; legal: yes, no] #ReportToSyslog=yes # User to run as. LCDd will drop its root priviledges, if any, # and run as this user instead. User=nobody # The server will stay in the foreground if set to true. #Foreground=no # Hello message: each entry represents a display line; default: builtin #Hello=" Welcome to" #Hello=" LCDproc!" Hello=" Wacken Death Box: Ready" Hello=" " Hello=" Construction: Ole Wolf, 2010" Hello=" wolf@blazingangles.com" # 1234567890123456789012345678901234567890 # GoodBye message: each entry represents a display line; default: builtin #GoodBye="Thanks for using" #GoodBye=" LCDproc!" GoodBye=" Shutting down. Stay heavy." GoodBye=" " GoodBye=" Construction: Ole Wolf, 2010" GoodBye=" wolf@blazingangles.com" # Sets the default time in seconds to displays a screen. WaitTime=5 # If yes, the the serverscreen will be rotated as a usual info screen. If no, # it will be a background screen, only visible when no other screens are # active. The special value 'blank' is similar to no, but only a blank screen # is displayed. [default: on; legal: on, off, blank] ServerScreen=no # Set master backlight setting. If set to 'open' a client may control the # backlight for its own screens (only). [default: open; legal: off, open, on] #Backlight=open # Set master heartbeat setting. If set to 'open' a client may control the # heartbeat for its own screens (only). [default: open; legal: off, open, on] Heartbeat=off # set title scrolling speed [default: 10; legal: 0-10] #TitleSpeed=10 # The "...Key=" lines define what the server does with keypresses that # don't go to any client. # These are the defaults: ToggleRotateKey=Enter PrevScreenKey=Left NextScreenKey=Right #ScrollUpKey=Up #ScrollDownKey=Down # If you have only 4 keys, you can choose to use this: #ToggleRotateKey=Enter #PrevScreenKey=Up #NextScreenKey=Down # If you have only 3 keys, you can choose to use this: #ToggleRotateKey=Enter #PrevScreenKey=Up ## The menu section. The menu is an internal LCDproc client. ## [menu] # You can configure what keys the menu should use. Note that the MenuKey # will be reserved exclusively, the others work in shared mode. # The following works excellent with 4 keys or more. MenuKey=Escape EnterKey=Enter UpKey=Up DownKey=Down # If you have 6 keys you may define these as well #LeftKey=Left #RightKey=Right # If you have only 3 keys, you could use something like this: #MenuKey=Escape #EnterKey=Enter #DownKey=Down ### Driver sections are below this line, in alphabetical order ### ## EMAC BayRAD driver ## [bayrad] # Select the output device to use [default: /dev/lcd] Device=/dev/lcd # Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200] Speed=9600 ## CrystalFontz driver (for CF632 & CF634) ## [CFontz] # Select the output device to use [default: /dev/lcd] Device=/dev/ttyS0 # Select the LCD size [default: 20x4] Size=20x4 # Set the initial contrast [default: 560; legal: 0 - 1000] Contrast=350 # Set the initial brightness [default: 1000; legal: 0 - 1000] Brightness=1000 # Set the initial off-brightness [default: 0; legal: 0 - 1000] # This value is used when the display is normally # switched off in case LCDd is inactive OffBrightness=0 # Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200 or 115200] Speed=9600 # Set the firmware version (New means >= 2.0) [default: no; legal: yes, no] NewFirmware=no # Reinitialize the LCD's BIOS [default: no; legal: yes, no] # normally you shouldn't need this Reboot=no ## CrystalFontz633 driver (for CF633 only) ## [CFontz633] # Select the output device to use [default: /dev/lcd] Device=/dev/ttyS0 # Select the LCD type (size) [default: 16x2] Size=16x2 # Set the initial contrast [default: 560; legal: 0 - 1000] Contrast=350 # Set the initial brightness [default: 1000; legal: 0 - 1000] Brightness=1000 # Set the initial off-brightness [default: 0; legal: 0 - 1000] # This value is used when the display is normally # switched off in case LCDd is inactive OffBrightness=50 # Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200, 115200] Speed=19200 # Set the firmware version (New means >= 2.0) [default: no; legal: yes, no] # Currently this flag is not in use, there is no such thing as NewFirmware. ;=) #NewFirmware=no # Reinitialize the LCD's BIOS [default: no; legal: yes, no] # I want to reboot the LCD to make sure we start from a known state Reboot=yes ## CrystalFontz packet driver (for CF631, CF633 & CF635) ## [CFontzPacket] # Select the LCD model [default: 633; legal: 631, 633, 635] Model=635 # Select the output device to use [default: /dev/lcd] Device=/dev/ttyUSB0 # Select the LCD size [default: depending on model: 635: 20x4, 631: 20x2, 633: 16x2] Size=20x4 # Set the initial contrast [default: 560; legal: 0 - 1000] Contrast=350 # Set the initial brightness [default: 1000; legal: 0 - 1000] Brightness=1000 # Set the initial off-brightness [default: 0; legal: 0 - 1000] # This value is used when the display is normally # switched off in case LCDd is inactive OffBrightness=50 # Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200, 115200] Speed=115200 # Set the firmware version (New means >= 2.0) [default: no; legal: yes, no] # Currently this flag is not in use, there is no such thing as NewFirmware. ;=) #NewFirmware=no # Reinitialize the LCD's BIOS [default: no; legal: yes, no] # I want to reboot the LCD to make sure we start from a known state Reboot=yes ## Curses driver ## [curses] # color settings # foreground color [default: blue] Foreground=blue # background color when "backlight" is off [default: cyan] Background=cyan # background color when "backlight" is on [default: red] Backlight=red # display size [default: 20x4] Size=20x4 # What position (X,Y) to start the left top corner at... # Default: (7,7) TopLeftX=7 TopLeftY=7 # use ASC symbols for icons & bars [default: no; legal, yes, no] UseACS=no # draw Border [default: yes; legal: yes, no] DrawBorder=yes ## Cwlinux driver ## [CwLnx] # Select the LCD model [default: 12232; legal: 12232, 12832, 1602] Model=12232 # Select the output device to use [default: /dev/lcd] Device=/dev/ttyUSB0 # Select the LCD size [default: depending on model: 12232: 20x4, 12832: 21x4, 1602: 16x2] Size=20x4 # Set the communication speed [default: 19200; legal: 9600, 19200] Speed=19200 # Reinitialize the LCD's BIOS [default: no; legal: yes, no] # normally you shouldn't need this Reboot=no # If you have a keypad connected. Keypad layout is currently not # configureable from the config file. Keypad=yes # If you have a non-standard keypad you can associate any keystrings to keys. # There are 6 input keys in the CwLnx hardware that generate characters # from 'A' to 'F'. # # The following is the built-in default mapping hardcoded in the driver. # You can leave those unchanged if you have a standard keypad. # You can change it if you want to report other keystrings or have a non # standard keypad. # KeyMap_A=Up # KeyMap_B=Down # KeyMap_C=Left # KeyMap_D=Right # KeyMap_E=Enter # KeyMap_F=Escape # keypad_test_mode permits to test keypad assignement # Default value is no #keypad_test_mode=yes ## ea65 driver for the display in AOpen XC Cube AV EA65 media barebones ## [ea65] # Device is fixed /dev/ttyS1 # Width and Height are fixed 9x1 # As the VFD is self luminescent we don't have a backlight # But we can use the backlight functions to control the front LEDs # Brightness 0 to 299 -> LEDs off # Brightness 300 to 699 -> LEDs half bright # Brightness 700 to 1000 -> LEDs full bright Brightness=500 # OffBrightness is the the value used for the 'backlight off' state OffBrightness=0 ## EyeboxOne driver ## [EyeboxOne] # Select the output device to use [default: /dev/ttyS1] #Device=/dev/cua01 Device=/dev/ttyS1 # Set the display size [default: 20x4] Size=20x4 # Switch on the backlight? [default: yes] Backlight=yes # Switch on the cursor? [default: no] Cursor=no # Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200] Speed=19200 # Enter Key is a \r character, so it's hardcoded in the driver LeftKey=D RightKey=C UpKey=A DownKey=B EscapeKey=P # You can find out which key of your display sends which # character by setting keypad_test_mode to yes and running # LCDd. LCDd will output all characters it receives. # Afterwards you can modify the settings above and set # keypad_set_mode to no again. keypad_test_mode=no ## g15 driver for Logitech G15 Keyboard LCDs ## [g15] # Display size (currently unused) size=20x5 ## glcdlib meta driver for graphical LCDs ## [glcdlib] ## mandatory: # which graphical display supported by graphlcd-base to use [default: image] # (see /etc/graphlcd.conf for possible drivers) Driver=noritake800 # no=use graphlcd bitmap fonts (they have only one size / font file) # yes=use fonts supported by FreeType2 (needs Freetype2 support in libglcdprocdriver and its dependants) UseFT2=yes # text resolution in fixed width characters [default: 16x4] # (if it won't fit according to available physical pixel resolutioni # and the minimum available font face size in pixels, then # 'DebugBorder' will automatically be turned on) TextResolution=20x4 # path to font file to use FontFile=/usr/share/fonts/corefonts/courbd.ttf ## these only apply if UseFT2=yes: # character encoding to use CharEncoding=iso8859-2 # minumum size in pixels in which fonts should be rendered MinFontFaceSize=7x12 ## optional: Brightness=50 # Brightness (in %) if applicable Contrast=50 # Contrast (in %) if applicable Backlight=no # Backlight if applicable UpsideDown=no # flip image upside down Invert=no # invert light/dark pixels ShowDebugFrame=no # turns on/off 1 pixel thick debugging # border whithin the usable text area, # for setting up TextResolution and # MinFontFaceSize (if using FT2); ShowBigBorder=no # border around the unused area ShowThinBorder=yes # border around the unused area PixelShiftX=0 PixelShiftY=2 ## Matrix Orbital GLK driver ## [glk] # select the serial device to use [default: /dev/lcd] Device=/dev/lcd # set the initial contrast value [default: 560; legal: 0 - 1000] Contrast=560 # set the serial port speed [default: 19200; legal: 9600, 19200, 38400] Speed=19200 ## Hitachi HD44780 driver ## [hd44780] # Select what type of connection. See documentation for types. ConnectionType=4bit # Port where the LPT is [ususal: 0x278, 0x378 and 0x3BC] Port=0x378 # Device of the serial interface [default: /dev/lcd] Device=/dev/ttyS0 # Bitrate of the serial port (0 for interface default) Speed=0 # If you have a keypad connected. # You may also need to configure the keypad layout further on in this file. Keypad=no # Set the initial contrast (bwctusb and lcd2usb) [default: 500; legal: 0 - 1000] Contrast=0 # Set brightness of the backlight (lcd2usb only) [default: 0; legal 0 - 1000] #Brightness=1000 #OffBrightness=0 # If you have a switchable backlight. Backlight=no # If you have the additional output port ("bargraph") and you want to # be able to control it with the lcdproc OUTPUT command OutputPort=no # Specifies if the last line is pixel addressable or it controls an # underline effect. [default: true (= pixel addressable); legal: yes, no] #Lastline=true # Specifies the size of the LCD. # In case of multiple combined displays, this should be the total size. Size=20x4 # For multiple combined displays: how many lines does each display have. # Vspan=2,2 means both displays have 2 lines. #vspan=2,2 # If you have an HD66712, a KS0073 or an other 'almost HD44780-compatible', # set this flag to get into extended mode (4-line linear). #ExtendedMode=yes # In extended mode, on some controllers like the ST7036 (in 3 line mode) # the next line in DDRAM won't start 0x20 higher. [default: 0x20] #LineAddress=0x10 # Character map to to map ISO-8859-1 to the LCD's character set # [default: hd44780_default; legal: hd44780_default, hd44780_euro, # ea_ks0073, sed1278f_0b ] CharMap=hd44780_default # If your display is slow and cannot keep up with the flow of data from # LCDd, garbage can appear on the LCDd. Set this delay factor to 2 or 4 # to increase the delays. Default: 1. #DelayMult=2 # Some displays (e.g. vdr-wakeup) need a message from the driver to that it # is still alive. When set to a value bigger then null the character in the # upper left corner is updated every seconds. Default: 0. #KeepAliveDisplay=0 # If you experience occasional garbage on your display you can use this # option as workaround. If set to a value bigger than null it forces a # full screen refresh seconds. Default: 0. #RefreshDisplay=5 # You can reduce the inserted delays by setting this to false. # On fast PCs it is possible your LCD does not respond correctly. # Default: true. DelayBus=true # If you have a keypad you can assign keystrings to the keys. # See documentation for used terms and how to wire it. # For example to give directly connected key 4 the string "Enter", use: # KeyDirect_4=Enter # For matrix keys use the X and Y coordinates of the key: # KeyMatrix_1_3=Enter KeyMatrix_4_1=Enter KeyMatrix_4_2=Up KeyMatrix_4_3=Down KeyMatrix_4_4=Escape ## ICP A106 driver ## [icp_a106] Device=/dev/ttyS1 ## Code Mercenaries IO-Warrior driver ## [IOWarrior] # display dimensions Size=20x4 # serial number [exactly as listed by usbview] # (if not given, the 1st IOWarrior found gets used) #SerialNumber=00000674 # If you have an HD66712, a KS0073 or an other 'almost HD44780-compatible', # set this flag to get into extended mode (4-line linear). #ExtendedMode=yes # Specifies if the last line is pixel addressable or it controls an # underline effect. [default: true (= pixel addressable); legal: yes, no] #Lastline=true ## Soundgraph/Ahanix/Silverstone/Uneed/Accent iMON driver ## [imon] # select the device to use Device=/dev/lcd0 # display dimensions Size=16x2 ## Soundgraph iMON LCD ## [imonlcd] # Specify which iMon protocol should be used [legal: 0=15c2:ffdc device, # 1=15c2:0038 device; default: 0] Protocol=0 # Set the exit behavior [legal: 0=leave shutdown message, 1=show the big clock, # 2=blank device; default: 1] #OnExit=2 # Select the output device to use [default: /dev/lcd0] Device=/dev/lcd0 # Select the displays contrast [default: 200; legal: 0-1000] Contrast=200 # Specify the size of the display in pixels [default: 96x16] #Size=96x16 # Set the backlight state [default: on; legal: on, off] #Backlight=on # Set the disc mode [legal: 0=spin the "slim" disc - two disc segments, # 1=their complement spinning; default: 0] #DiscMode=0 ## IrMan driver ## [IrMan] # in case of trouble with IrMan, try the Lirc emulator for IrMan # Select the input device to use #Device=/dev/irman # Select the configuration file to use #Config=/etc/irman.cfg ## IRtrans driver ## [irtrans] # Does the device have a backlight? [default: no; legal: yes, no] #Backlight=no # IRTrans device to connect to [default: localhost] #Hostname=localhost # display dimensions Size=16x2 ## Joystick driver ## [joy] # Select the input device to use [default: /dev/js0] Device=/dev/js0 # set the axis map Map_Axis1neg=Left Map_Axis1pos=Right Map_Axis2neg=Up Map_Axis2pos=Down # set the button map Map_Button1=Enter Map_Button2=Escape ## LB216 driver ## [lb216] # Select the output device to use [default: /dev/lcd] Device=/dev/lcd # Set the initial brightness [default: 255; legal: 0 - 255] Brightness=255 # Set the communication speed [default: 9600; legal: 2400, 9600] Speed=9600 # Reinitialize the LCD's BIOS [default: no; legal: yes, no] Reboot=no ## LCDM001 driver ## [lcdm001] Device=/dev/ttyS1 # keypad settings # Keyname Function # Normal context Menu context # ------- -------------- ------------ # PauseKey Pause/Continue Enter/select # BackKey Back(Go to previous screen) Up/Left # ForwardKey Forward(Go to next screen) Down/Right # MainMenuKey Open main menu Exit/Cancel PauseKey=LeftKey BackKey=UpKey ForwardKey=DownKey MainMenuKey=RightKey # You can rearrange the settings here. # If your device is broken, have a look at server/drivers/lcdm001.h ## HNE LCTerm driver ## [lcterm] Device=/dev/ttyS1 Size=16x2 ## LIRC input driver ## [lirc] # Specify an alternative location of the lircrc file [default: ~/.lircrc] #lircrc=/etc/lircrc.lcdproc # Must be the same as in your lircrc #prog=lcdd ## LIS MCE 2005 driver ## [lis] # Set the initial brightness [default: 1000; legal: 0 - 1000] # 0-250 = 25%, 251-500 = 50%, 501-750 = 75%, 751-1000 = 100% #Brightness=1000 # Columns by lines [default: 20x2] #Size=20x2 # USB Vendor ID [default: 0x0403] # Change only if testing a compatible device. #VendorID=0x0403 # USB Product ID [default: 0x6001] # Change only if testing a compatible device. #ProductID=0x6001 ##The driver for the VFD of the Medion MD8800 PC ## [MD8800] # device to use [default: /dev/ttyS1] #Device=/dev/ttyS1 # display size [default: 16x2] #Size=16x2 # Set the initial brightness [default: 1000; legal: 0 - 1000] Brightness=1000 # Set the initial off-brightness [default: 0; legal: 0 - 1000] # This value is used when the display is normally # switched off in case LCDd is inactive OffBrightness=50 ## MSI MS-6931 driver for displays in 1HU servers ## [ms6931] # device to use [default: /dev/ttyS1] Device=/dev/ttyS1 # display size [default: 16x2] #Size=16x2 ## MTC-S16209x driver ## [mtc_s16209x] # Select the output device to use [default: /dev/lcd] Device=/dev/lcd # Set the initial brightness [default: 255; legal: 0 - 255] Brightness=255 # Reinitialize the LCD's BIOS [default: no; legal: yes, no] Reboot=no ## Matrix Orbital driver ## [MtxOrb] # Select the output device to use [default: /dev/lcd] Device=/dev/ttyS0 # Set the display size [default: 20x4] Size=40x4 # Set the display type [default: lcd; legal: lcd, lkd, vfd, vkd] Type=lkd # Set the initial contrast [default: 480] # NOTE: The driver will ignore this if the display # is a vfd or vkd as they don't have this feature Contrast=400 # Some old displays do not have an adjustable backlight but only can # switch the backlight on/off. If you experience randomly appearing block # characters, try setting this to false. [default: yes; legal: yes, no] hasAdjustableBacklight=yes # Set the initial brightness [default: 1000; legal: 0 - 1000] Brightness=500 # Set the initial off-brightness [default: 0; legal: 0 - 1000] # This value is used when the display is normally # switched off in case LCDd is inactive OffBrightness=0 # Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200] #Speed=19200 Speed=115200 # The following table translates from MtxOrb key letters to logical key names. # By default no keys are mapped, meaning the keypad is not used at all. #KeyMap_A=Left #KeyMap_B=Right #KeyMap_C=Up #KeyMap_D=Down #KeyMap_E=Enter #KeyMap_F=Escape KeyMap_A=a KeyMap_B=b KeyMap_C=c KeyMap_D=d KeyMap_E=e KeyMap_F=f KeyMap_G=g KeyMap_H=h KeyMap_I=i KeyMap_J=j KeyMap_K=k KeyMap_L=l KeyMap_M=m KeyMap_N=n KeyMap_O=o KeyMap_P=p KeyMap_Q=q KeyMap_R=r KeyMap_S=s KeyMap_T=t KeyMap_U=u KeyMap_V=v KeyMap_W=w KeyMap_X=x KeyMap_Y=y # See the [menu] section for an explanation of the key mappings # You can find out which key of your display sends which # character by setting keypad_test_mode to yes and running # LCDd. LCDd will output all characters it receives. # Afterwards you can modify the settings above and set # keypad_set_mode to no again. keypad_test_mode=no ## mx5000 driver for LCD display on the Logitech MX5000 keyboard ## [mx5000] # Select the output device to use [default: /dev/hiddev0] Device = /dev/hiddev0 # Time to wait in ms after the refresh screen has been sent [default: 1000] WaitAfterRefresh = 1000 ## Noritake VFD driver ## [NoritakeVFD] # device where the VFD is. Usual values are /dev/ttyS0 and /dev/ttyS1 [default: /dev/lcd] Device=/dev/ttyS0 # Specifies the size of the LCD. Size=20x4 # Set the initial brightness [default: 1000; legal: 0 - 1000] Brightness=1000 # Set the initial off-brightness [default: 0; legal: 0 - 1000] # This value is used when the display is normally # switched off in case LCDd is inactive OffBrightness=50 # set the serial port speed [default: 9600, legal: 1200, 2400, 9600, 19200, 115200] Speed=9600 # Set serial data parity [default: 0 (None), legal: 0(=none), 1(=odd), 2(=even)] Parity=0 # re-initialize the VFD [default: no; legal: yes, no] Reboot=no ## Mini-box.com picoLCD (usblcd) driver ## [picolcd] # KeyTimeout is the time that LCDd spends waiting for a key press before cycling # through other duties. Higher values make LCDd use less CPU time and make # key presses more detectable. Lower values make LCDd more responsive but a # little prone to missing key presses. 500 (.5 second) is the default and a # balanced value. KeyTimeout=500 # Set the initial brightness [default: 1000; legal: 0 - 1000] Brightness=1000 # Set the initial contrast [default: 1000; legal: 0 - 1000] Contrast=1000 # Light the keys? i[default: on; legal: on, off] Keylights=on # If Keylights is on, the you can unlight specific keys below: # Key0 is the directional pad. Key1 - Key5 correspond to the F1 - F5 keys. # There is no LED for the +/- keys. This is a handy way to indicate to users # which keys are disabled. [default: on; legal: on, off] Key0Light=on Key1Light=on Key2Light=on Key3Light=on Key4Light=on Key5Light=on # Host name or IP address of the LIRC instance that is to receive IR codes # If not set, or set to an empty value, IR support is disabled. #LircHost=127.0.0.1 # UDP port on which LIRC is listening [default: 8765; legal: 1 - 65535] LircPort=8765 # Duration in jiffies of the synthesized sync pulse [default: 64; 0 to suppress] LircSync=64 # Duration in jiffies of the synthesized gap; 0 to suppress, default 2048. # This is really the fixed duration of an entire IR command; individual pulse/space # durations are deducted from this to determine the duration of the trailing gap. LircLength=2048 ## Pyramid LCD driver ## [pyramid] # device to connect to [default: /dev/lcd] Device=/dev/ttyUSB0 ## Seiko Epson 1330 driver ## [sed1330] # Port where the LPT is. Common values are 0x278, 0x378 and 0x3BC Port=0x378 # Type of LCD module (legal: G321D, G121C, G242C, G191D, G2446, SP14Q002) # Note: Currently only tested with G321D & SP14Q002. Type=G321D # Width x Height of a character cell in pixels [legal: 6x7 - 8x16; default: 6x10] CellSize=6x10 # Select what type of connection [legal: classic, bitshaker; default: classic] ConnectionType=classic ## Seiko Epson 1520 driver ## [sed1520] # Port where the LPT is. Usual values are 0x278, 0x378 and 0x3BC Port=0x378 ## serial POS display driver ## [serialPOS] # Device to use in serial modea [default: /dev/lcd] Device=/dev/lcd # Specifies the size of the display in characters. [default: 16x2] Size=16x2 # Set the communication protocol to use with the POS display. # [default: AEDEX; legal: IEE, Epson, Emax, IBM, LogicControls, Ultimate] Type=AEDEX # communication baud rate with the display [default: 9600; legal: 1200, 2400, 19200, 115200] Speed=9600 ## Serial VFD driver ## ## Drives various (see below) serial 5x7dot VFD's. ## [serialVFD] # Specifies the displaytype.[default: 0] # 0 NEC (FIPC8367 based) VFDs. # 1 KD Rev 2.1. # 2 Noritake VFDs (*). # 3 Futaba VFDs # 4 IEE S03601-95B # 5 IEE S03601-96-080 (*) # 6 Futaba NA202SD08FA (allmost IEE compatible) # 7 Samsung 20S207DA4 and 20S207DA6 # 8 Nixdorf BA6x / VT100 # (* most should work, not testet yet.) Type=0 # "no" if display connected serial, "yes" if connected parallel. [default: no(=serial)] use_parallel=no # Number of Custom-Characters [default: displaytype dependent] #Custom-Characters=0 # Portaddress where the LPT is. Used in parallelmode only. Usual values are 0x278, 0x378 and 0x3BC Port=0x378 # Set parallel port timingdelay (us). Used in parallelmode only. [default: 2; legal: 0 - 255] #PortWait=2 # Device to use in serial mode. Usual values are /dev/ttyS0 and /dev/ttyS1 Device=/dev/ttyS1 # Specifies the size of the VFD. Size=20x2 # Set the initial brightness [default: 1000; legal: 0 - 1000] # (4 steps 0-250, 251-500, 501-750, 751-1000) Brightness=1000 # Set the initial off-brightness [default: 0; legal: 0 - 1000] # This value is used when the display is normally # switched off in case LCDd is inactive # (4 steps 0-250, 251-500, 501-750, 751-1000) OffBrightness=0 # set the serial port speed [default: 9600; legal: 1200, 2400, 9600, 19200, 115200] Speed=9600 # enable ISO 8859 1 compatibility [default: yes; legal: yes, no] #ISO_8859_1=yes ## shuttleVFD driver ## [shuttleVFD] # No options ## stv5730 driver ## [stv5730] # Port the device is connected to [default: 0x378] Port=0x378 ## SVGAlib driver ## [svga] # svgalib mode to use [default: G320x240x256; legal: supported svgalib modes] #Mode=G640x480x256 # set display size [default: 20x4] Size=20x4 # Set the initial contrast [default: 500; legal: 0 - 1000] # Can be set but does not change anything internally Contrast=500 # Set the initial brightness [default: 1000; legal: 1 - 1000] Brightness=1000 # Set the initial off-brightness [default: 500; legal: 1 - 1000] # This value is used when the display is normally # switched off in case LCDd is inactive OffBrightness=500 ## Text driver ## [text] # Set the display size [default: 20x4] Size=20x4 ## Toshiba T6963 driver ## [t6963] # set display size [default: 20x6] Size=20x6 # port to use [default: 0x378; legal: 0x200 - 0x400] Port=0x378 # Is ECP mode on? [default: yes; legal: yes, no] #ECPlpt=yes # Use graphics? [default: no; legal: yes, no] #graphic=no ## Tyan Barebones LCD driver (GS10 & GS12 series) ## [tyan] # Select the output device to use [default: /dev/lcd] Device=/dev/lcd # Set the communication speed [default: 9600; legal: 4800, 9600] Speed=9600 # set display size [default: 16x2] Size=16x2 ## ELV ula200 driver ## [ula200] # Select the LCD size [default: 20x4] Size=20x4 # If you have a non standard keypad you can associate any keystrings to keys. # There are 6 input key in the CwLnx hardware that generate characters # from 'A' to 'F'. # # The following it the built-in default mapping hardcoded in the driver. # You can leave those unchanged if you have a standard keypad. # You can change it if you want to report other keystrings or have a non # standard keypad. # KeyMap_A=Up # KeyMap_B=Down # KeyMap_C=Left # KeyMap_D=Right # KeyMap_E=Enter # KeyMap_F=Escape ## Wirz SLI LCD driver ## [sli] # Select the output device to use [default: /dev/lcd] Device=/dev/lcd # Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200, 38400, 57600, 115200] Speed=19200 ## OnScreen Display using libxosd ## [xosd] # set display size [default: 20x4] Size=20x4 # Offset in pixels from the top-left corner of the monitor [default: 0x0] Offset=200x200 # X font to use, in XLFD format, as given by "xfontsel" Font=-*-terminus-*-r-*-*-*-320-*-*-*-*-* # EOF